Publication

Journal

  1. Yahya, A. and Manning,i C.D. (2004) Determination of material removal rate of an electro-discharge machine using dimensional analysis. J. Phys. D: Appl. Phys. 37 1467-1471 (IF=2.083)
  2. Azli Yahya, Ade Erawan Minhat, Trias Andromeda Abd Rachim, Nor Hisham Hj Khamis, Kamal Khalil & Muhammad Arif “Communication Within Hardware Of Electrical Discharge Machining (EDM) System”. Jurnal Teknologi Special Edition, No.55, Mei 2011, pp. 201-211. (Indexed by SCOPUS)
  3. Andromeda T, Yahya A, Baharom A, RahimM A A, Mahmud N (2011) Material Removal Rate Prediction of Electrical DischargeMachining Process Using Artificial Neural Network, Journalof Mechanics Engineering and Automation (JMEA) (Indexed by EBSCO)
  4. Yahya A,Andromeda T, Minhat A E, Khamis N H, Khalil K and Rahim M A A (2012) ComparisonStudies of Electrical Discharge Machining (EDM) Process Model for Low GapCurrent, Advanced Materials Research Journal(ISSN: 1022-6680) (Indexedby SCOPUS)
  5. Tiong Chiong Ing, A. K. Mohammed Rafiq, Y. Azli and S. Syahrullail (2012) The effect of temperature on the tribological behaviour of RBD palm stearin, Tribology Transaction (ISSN: 1040-2004 (Print), 1547-397X (Online)) (IF=0.669)
  6. Tiong Chiong Ing, Yahya Azli, Abdul Kadir Mohammed Rafiq, Samion Syahrullail (2012) Tribological evaluation of refined, bleached and deodorized (RBD) palm stearin using fourball tribotester with different normal load, Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering) (ISSN: 1673-565X (Print); ISSN 1862-1775 (Online)) (IF=0.326)

 International Conference

  1. Yahya A and Manning C D (2003) Modelling and simulation of Die Sinking Electro discharge machine systems. 3rd Asian Conf. on Industrial Automation and Robotics (Thailand) pp 1–4
  2. Yahya, A. and Manning, C.D. (2003) Modelling and Simulation of Electro Discharge Machine Systems, PREP2003, Exeter (UK), April
  3. Yahya, A.(2003) Modelling and Controller Design for EDM System Based on DSPMicroprocessor, MRG Manchester(UK),Sept.
  4. Yahya, A. and Manning, C.D. (2003) Modelling, Simulation and Controller Design for Electro Discharge Machine System, ESC Division Research, Leicestershire (UK), Sept., 21-23
  5. Yahya A. (2004) Material removal rate prediction of electro-discharge machine, MRG, Manchester, April, UK
  6. Yahya, A and Manning, C.D. (2005) Material removal rate modeling of an electro-discharge machine, Power Electronic Division, Sutton Bonington (UK), April
  7. Tri Basuki Kurniawan, Zuwairie Ibrahim, Muhammad Faiz Mohamed Saaid, and Azli Yahya, (2008) Implementation of Ant System for DNA Sequence Optimization, NANO-SciTech 2008, Shah Alam, Malaysia, 18-21 November
  8. Saaid M.F.M, Ibrahim Z, Khalid M and Yahya A (2008) Alternative Fuzzy C-Means Clustering for DNA Computing Readout Method Implemented on DNA Engine Opticon 2 System. SITIS08, Bali (INDONESIA), December
  9. Yahya, A. and Khamis, N.H.H (2009) Servomechanism Study of an Electrical Discharge Machining (EDM) System, EMAP2009, Penang, Malaysia, December
  10. Andromeda, T.,Yahya, A. and Khamis, N.H.H (2010)  Predicting Material Removal Rate of ElectricalDischarge Machining (EDM) using Artificial Neural Network for low Igap current, ICEM2010, Kuala Lumpur, Malaysia,November
  11. Azahar M, Andromeda T, Yahya A, Zulkiflee R, Arif M and Rafiq M (2011) Low Cost Gel Electrophoresis Unit with New Design Improvement, I-ENVEX2011, UniMAP poster publication
  12. Andromeda T ,Yahya A, Khamis N H, Khalil K, Minhat A E (2011) Predicting Material RemovalRate of Electrical Discharge Machining (EDM) using Artificial Neural Networkfor High Igap Current, INECCE2011, UMP Pahang, Malaysia (Scopus Indexed)
  13. Yahya A, Andromeda T, Minhat A E, Khamis N H, Khalil K and Rahim M A A (2011) Comparison Studies of Electrical Discharge Machining (EDM) Process Model for Low Gap Current, ICMST2011, Singapore, September – (Scopus Indexed)- Award for Excellent paper
  14. Nor Liyana Safura Hashim, Azli Yahya, Mohammed Rafiq Abdul Kadir, Syahrullail Samion, Nazriah Mahmud (2012). Manufacturing Methods for Machining Micro Pits of Hip Implant for Metal-on-Metal Lubrication. 2012 International Conference of Biomedical Engineering (ICoBE), Penang, Malaysia, IEEE Xplore and SCOPUS.
  15. Nazriah Mahmud, Azli Yahya, Mohammed Rafiq, Syahrullail Samion , Nor Liyana Safura. Electrical Discharge Machining Pulse Power Generator to Machine Micropits of Hip Implant. in 2012 International Conference on Biomedical Engineering (ICoBE). 2012. Penang, Malaysia: IEEE Xplore and SCOPUS
  16. A. Yahya, T.Andromeda, M. Arif Abdul Rahim, Ameruddin Baharom, “Erosion Rate ModelComparison of Electrical Discharge Machining Process”, ICIAS2012, Kuala Lumpur,Malaysia, 12-14 June 2012.
  17. T. Andromeda,A. Yahya, N H Haji Khamis, Ameruddin Baharom, M. Arif Abdul Rahim, “PIDController Tuning by Particle Swarm Optimization on Electrical DischargeMachining Servo Control System”, ICIAS2012, Kuala Lumpur, Malaysia, 12-14 June2012.
National Conference
  1. Yahya, A and Manning, C.D. (2007) Modelling, Simulation and Experimentation of an Electro Discharge Machining (EDM) System, CIM07 (UTM)

Other

  1. Book Chapters, (2008) Advances in Digital Systems, UTM, December
  2. Article in Magazine, FKBSK (2009)
  3. Book 2011 – Digital Electronics Compact Notes, LAP Lambert Academic Publishing ISBN 978-3-8454-7618-6
Comments